Two ways to attach a #HANDMADE label
The #HANDMADE woven label from Sublime Stitching is a sew-in label, not an iron-on. You have two supported methods: fold the label in half and insert it along a seam, or apply it flat against the fabric. Both work on hand-stitched and hand-crafted projects, and both rely on your needle and thread to hold the label in place.
Each label is pre-cut and measures 3" long by 5/8" wide (7.6 cm by 1.6 cm). The ends are heat-sealed to prevent fraying, so you can handle the label without worrying about the edges unraveling before you sew. You get four labels per pack.
Label specs that affect your sewing plan
- Woven Labels - #HANDMADE: Four pre-cut, sew-in labels per pack; each measures 3" long x 5/8" wide (7.6 cm x 1.6 cm). Knowing the exact size helps you choose a seam allowance and placement spot before you start stitching.

Woven Labels - #HANDMADE - Woven Labels - #HANDMADE: Ends are heat-sealed so they won't fray. You can skip edge-finishing steps and sew the label as-is, saving time and avoiding bulk.
- Woven Labels - #HANDMADE: Affix by folding in half and inserting along the seam, or apply flat. These are the two supported attachment methods; pick the one that suits your project's construction.
Fold-and-insert method for seam placement
This method hides the label's raw ends inside a seam and works well on bags, pouches, and garment side seams. The label becomes part of the seam allowance, so plan your sewing order accordingly.
- Choose your seam: Pick a seam that will be sewn after the label is inserted, such as a side seam or bottom edge. The label will be enclosed when the seam is stitched.
- Fold the label in half: Fold the label so the short ends meet. The fold creates a loop that will sit outside the seam, while the ends are caught inside.
- Insert along the seam line: Place the folded label between the fabric layers at the seam line, with the loop facing inward (toward the project's interior) or outward as you prefer. Pin or baste to hold it.
- Sew the seam: Stitch the seam as you normally would, catching the label's ends in the stitching. Backstitch over the label area for security.
- Check the result: Turn the project right side out and confirm the label sits flat and the ends are securely enclosed. If any part of the label escaped the seam, unpick and resew that section.
Flat application for surface placement
Flat application suits projects where you want the label visible on the surface, such as the front of a hoop art piece or the outside of a finished pouch. The label lies flat against the fabric and is stitched around its perimeter.
- Position the label: Place the label where you want it, right side up. Use a pin or a small dab of water-soluble glue to hold it in place if needed.
- Thread your needle: Use a hand-sewing needle and thread that matches or contrasts with the label, depending on your design. A single strand of embroidery floss also works.
- Stitch around the edges: Sew a running stitch or backstitch close to the label's perimeter, going through the label and the fabric beneath. Keep stitches small and even for a neat finish.
- Secure the corners: Add extra stitches at each corner to prevent the label from lifting. Bury the thread tail between the layers and trim.
- Press gently: Press the area with a cool iron if needed, but avoid direct heat on the label's heat-sealed ends. Always test on a scrap first.
Placement tips for handmade woven labels
Where you put the label affects both its visibility and its durability. Consider these guidelines when deciding on handmade woven label placement.
- Inside a seam: Best for a clean, professional look on garments and bags. The label is hidden inside, with only the loop visible if you choose.
- Along a hem or edge: A flat-applied label near a hem or edge draws the eye without interfering with the project's structure.
- On the back of hoop art: Attach the label flat to the back of the hoop, covering the fabric's raw edges or the hoop's back. This adds a finished touch and identifies your work.
- Avoid high-stress areas: Skip spots that stretch or rub frequently, such as underarms or tight corners. The label may wear faster there.
Sewing tips for a secure, neat finish
Use a sharp hand-sewing needle and a thread that matches the label's weight. A single strand of embroidery floss is a good option if you want a decorative touch. Keep your stitches small and close together to distribute stress evenly across the label.
Because the ends are heat-sealed, you don't need to fold them under or apply fray check. However, avoid cutting the label shorter, as that would expose unsealed edges. If you must trim, seal the new edge with a tiny dab of fabric glue and let it dry completely before sewing.
When sewing through the label, aim for the woven area rather than the sealed ends. The sealed ends are stiffer and may resist the needle. If you're using a machine, a size 80/12 needle works well for most woven labels, but always test on a scrap first.
What you get in the pack
- Woven Labels - #HANDMADE: Four pre-cut, sew-in labels per pack; each measures 3" long x 5/8" wide (7.6 cm x 1.6 cm). Four labels let you practice on a sample and still have enough for multiple finished pieces.
- Woven Labels - #HANDMADE: Affix to hand-stitched or hand-crafted projects by folding in half and inserting along the seam, or applying flat. The labels are designed for handwork, so they suit embroidery, quilting, and other slow crafts.
- Woven Labels - #HANDMADE: Not made by robots! A reminder that these labels are a handmade-friendly supply, matching the spirit of your projects.


